New Construction Wiring & Installation in Cypress, TX

Custom home construction is where new construction electrical work gets interesting, because the plan changes. A homeowner walks the framed house, sees the space for the first time, and wants two more cans in the kitchen and an outlet where the coffee bar is going. That is normal. What matters is having an electrician on the job who can absorb a change without blowing up the schedule or the budget.

We wire custom homes for builders across Cypress, Katy, Tomball, Spring, Jersey Village, and the surrounding Northwest Houston communities. On a custom build we walk the house with the homeowner or the builder at rough-in, mark device locations on the studs, and confirm the plan before a single wire goes in the wall. It takes an afternoon and it prevents most of the change orders that would otherwise land later.

We also handle the parts of a custom home that fall outside a standard wiring package: outdoor kitchen circuits, pool and spa lighting, landscape and exterior lighting runs, workshop and garage subpanels, and whole home generator provisions if backup power is part of the plan.

A few decisions cost almost nothing during rough-in and get expensive once the house is closed in. If you are building now, think through these while the walls are still open:

Commercial new construction runs on a different clock than residential. There are more trades on site, more coordination meetings, and a general contractor who needs to know your crew will be where they said they would be. We work as the electrical contractor on new commercial buildings across the Houston area, and we work the way a GC needs an electrical sub to work: on the schedule, on the plans, and reachable.

Our commercial new construction electrical work covers service and distribution equipment, three-phase installations, panel and transformer sets, feeders and branch circuits, lighting and lighting control rough-in, exit and emergency lighting, exterior and parking area lighting, data and communications rough-in, and equipment connections for the mechanical and kitchen trades.

Not every commercial job starts and ends at the same time. Shell construction and tenant improvement work often run months apart, and the electrical decisions made during the shell phase determine how easy or painful the buildout is later.

We handle both sides. On a shell building we set the service, distribution, and house panels with enough capacity and enough spare conduit for the tenants who have not signed yet. On a tenant buildout we work inside an existing shell, add the panels and circuits the space actually needs, and coordinate with the property manager on after-hours work when the rest of the building is occupied.

If you have not built before, here is how our part of the job sequences against yours.

We bid from your prints, not from a square footage guess. That means reading the electrical plan against the mechanical and appliance schedules, running the load calculation, and confirming the service size works for the finished building. If the plan is missing something or the service looks light for what is being installed, you hear about it during the bid rather than during construction.

Rough-in is where the house gets its bones. Home runs, branch circuits, boxes, and device backing all go in while the framing is open. We install to the plan and to the current electrical code, and we mark our work so the inspector, the insulator, and the drywall crew all know what they are looking at.

After the walls are closed and painted, we come back for devices, cover plates, fixtures, ceiling fans, and panel labeling. Then we energize the system, test the circuits, and walk the final inspection with you. A labeled panel and a working set of circuits at handoff is the difference between a clean close-out and a punch list.

Most of Cypress sits in unincorporated Harris County, and that changes which office issues your permit and who inspects the work compared to a build inside Houston city limits. Nearby projects in Jersey Village, Tomball, or Katy can fall under a different jurisdiction entirely, sometimes on the other side of the same road.

We pull the electrical permits our scope requires and coordinate inspections with your build schedule. If your project sits on a jurisdictional line, we sort out which office it falls under before we start rather than after an inspector turns the job down.

Picking an electrical contractor for a new build usually comes down to whether they are still responsive at trim-out. Here is what working with us looks like:

Our work on a build does not end at final inspection. Punch list items, callbacks during your warranty period, and the calls that come months after the buyer has the keys all get handled the same way. An outlet quits. Lights flicker in one room. A breaker keeps tripping. A garage door opener has no power. Call us and we will get someone out. If you build homes around Cypress and the Northwest Houston area, that means you have an electrician to send when a buyer calls you six months after closing.